對這文章發表回應
發表限制: 非會員 可以發表
發表者： 冷日 發表時間： 2019/5/31 13:41:05
Monitoring CPU Usage
The uptime, mpstat, sar, dstat, and top utilities allow you to monitor CPU usage. When a system's CPU cores are all occupied executing the code of processes, other processes must wait until a CPU core becomes free or the scheduler switches a CPU core to run their code. If too many processes are queued too often, this can represent a bottleneck in the performance of the system.
The commands mpstat -P ALL and sar -u -P ALL display CPU usage statistics for each CPU core and averaged across all CPU cores.
The %idle value shows the percentage of time that a CPU was not running system code or process code. If the value of %idle is near 0% most of the time on all CPU cores, the system is CPU-bound for the workload that it is running. The percentage of time spent running system code (%systemor %sys) should not usually exceed 30%, especially if %idle is close to 0%.
The system load average represents the number of processes that are running on CPU cores, waiting to run, or waiting for disk I/O activity to complete averaged over a period of time. On a busy system, the load average reported by uptime or sar -q should usually be not greater than two times the number of CPU cores over periods as long as 5 or 15 minutes. If the load average exceeds four times the number of CPU cores for long periods, the system is overloaded.
In addition to load averages (ldavg-*), the sar -q command reports the number of processes currently waiting to run (the run-queue size, runq-sz) and the total number of processes (plist_sz). The value of runq-sz also provides an indication of CPU saturation.
Determine the system's average load under normal loads where users and applications do not experience problems with system responsiveness, and then look for deviations from this benchmark over time. A dramatic rise in the load average can indicate a serious performance problem.
A combination of sustained large load average or large run queue size and low %idle can indicate that the system has insufficient CPU capacity for the workload. When CPU usage is high, use a command such as dstat or top to determine which processes are most likely to be responsible. For example, the following dstat command shows which processes are using CPUs, memory, and block I/O most intensively:
The top command provides a real-time display of CPU activity. By default, top lists the most CPU-intensive processes on the system. In its upper section, top displays general information including the load averages over the past 1, 5 and 15 minutes, the number of running and sleeping processes (tasks), and total CPU and memory usage. In its lower section, top displays a list of processes, including the process ID number (PID), the process owner, CPU usage, memory usage, running time, and the command name. By default, the list is sorted by CPU usage, with the top consumer of CPU listed first. Type f to select which fields top displays, o to change the order of the fields, or O to change the sort field. For example, entering On sorts the list on the percentage memory usage field (%MEM).
原文出處：8.2.2.1 Monitoring CPU Usage
The uptime, mpstat, sar, dstat, and top utilities allow you to monitor CPU usage. When a system's CPU cores are all occupied executing the code of processes, other processes must wait until a CPU core becomes free or the scheduler switches a CPU core to run their code. If too many processes are queued too often, this can represent a bottleneck in the performance of the system.
The commands mpstat -P ALL and sar -u -P ALL display CPU usage statistics for each CPU core and averaged across all CPU cores.
The %idle value shows the percentage of time that a CPU was not running system code or process code. If the value of %idle is near 0% most of the time on all CPU cores, the system is CPU-bound for the workload that it is running. The percentage of time spent running system code (%systemor %sys) should not usually exceed 30%, especially if %idle is close to 0%.
The system load average represents the number of processes that are running on CPU cores, waiting to run, or waiting for disk I/O activity to complete averaged over a period of time. On a busy system, the load average reported by uptime or sar -q should usually be not greater than two times the number of CPU cores over periods as long as 5 or 15 minutes. If the load average exceeds four times the number of CPU cores for long periods, the system is overloaded.
In addition to load averages (ldavg-*), the sar -q command reports the number of processes currently waiting to run (the run-queue size, runq-sz) and the total number of processes (plist_sz). The value of runq-sz also provides an indication of CPU saturation.
Determine the system's average load under normal loads where users and applications do not experience problems with system responsiveness, and then look for deviations from this benchmark over time. A dramatic rise in the load average can indicate a serious performance problem.
A combination of sustained large load average or large run queue size and low %idle can indicate that the system has insufficient CPU capacity for the workload. When CPU usage is high, use a command such as dstat or top to determine which processes are most likely to be responsible. For example, the following dstat command shows which processes are using CPUs, memory, and block I/O most intensively:
# dstat --top-cpu --top-mem --top-bio
The top command provides a real-time display of CPU activity. By default, top lists the most CPU-intensive processes on the system. In its upper section, top displays general information including the load averages over the past 1, 5 and 15 minutes, the number of running and sleeping processes (tasks), and total CPU and memory usage. In its lower section, top displays a list of processes, including the process ID number (PID), the process owner, CPU usage, memory usage, running time, and the command name. By default, the list is sorted by CPU usage, with the top consumer of CPU listed first. Type f to select which fields top displays, o to change the order of the fields, or O to change the sort field. For example, entering On sorts the list on the percentage memory usage field (%MEM).
原文出處：8.2.2.1 Monitoring CPU Usage